Phones answered 24/7New Bedford, MA
Call (833) 751-2102
Phones answered 24/7Call any time(833) 751-2102
Guide

What a three-story roof asks of a crew

Why a New Bedford triple-decker roof needs staging, careful wall flashing and a plan for the flat or low-slope deck, from the wall edge to the rear porch.

Illustration for the guide "What a three-story roof asks of a crew" (New Bedford, MA)
Short answer

A triple-decker is three stories of wall under a roof that is often flat, low-slope or hidden behind a parapet, with a rear ell and porch roofs beside it. The job turns on access, the flashing at each wall and the drainage of the low-slope deck, and each of those is handled differently from a single gable.

Key takeaways

  • A triple-decker is a three-story wood-frame house with one household stacked over the next, and its roof is usually more than one roof.
  • The eave sits high above the ground, so the crew plans its route, its staging and its fall protection before the first tear-off.
  • A low-slope deck sheds water slowly, so its seams, edges and drains decide whether it keeps water out.
  • The wall-to-roof junction and the chimney are the usual leak points, and a stain on an upper ceiling often starts well away from the stain.
  • Occupied units affect the sequence of the work, the access and the notice that tenants or owners need.
  • A sound triple-decker scope names each roof section, each junction and the drains as separate items.

Why are triple-deckers so common in these cities?

Much of New Bedford and Fall River was built as multi-family housing before the Second World War, and the triple-decker is the typical form.

The triple-decker is a three-story wood-frame house with a flat or low-pitch roof, one apartment stacked above the next, and stairs or porches running up the rear. Many were built in the decades around the turn of the last century, when mill work drew families to both cities and they needed rented housing close to the job.

Fall River's housing is also mostly pre-1940, according to a local commentator quoted in a regional news report, and the same report describes the city's stock as dominated by this form. New Bedford's older stock follows a similar pattern of multi-family wood-frame houses on narrow lots, though the mix of gables and triple-deckers varies by neighborhood.

The share of triple-deckers in New Bedford specifically is not a figure this guide can give, because no reliable count was found. What can be said is that the form is common enough to shape how roofers work in both cities, and a crew that has not worked on one should expect the differences set out here.

What makes the roof of a three-story house harder to reach?

Height, the rear ell and the narrow lot mean the roof is reached from a ladder, a tower or the rear porch, and the crew plans that route before the first tear-off.

The eave of a three-story house sits well above the reach of a standard extension ladder from the ground, and the rear ell or porch roof is often lower than the main roof. A crew may work from the rear, use a tower or stage a platform on the porch, and each choice changes the safety plan and the time needed.

Narrow side yards limit the room for a crew line or a debris chute along the house. Materials are often carried by hand up stairs, through a rear entry or hoisted by rope to the top floor, and that carrying is labor the scope should name rather than assume.

Ask the crew how it will reach the top roof, where material will be staged and how the tenants of each unit will be told about the work. An occupied house has more to protect than an empty one, and a plan that ignores the people inside is an incomplete plan.

How is a flat or low-slope deck different?

A low-slope deck sheds water slowly, so it depends on a tight membrane or seam, on its drainage and on its edges, and a small failure holds water that finds the way in.

Triple-deckers often have a flat or low-slope top roof and porch roofs, and these carry water differently from a steep covering. Water moves across them slowly and collects where the surface dips, so any failed seam or lifted edge holds water rather than shedding it.

The usual repair is to replace the membrane or covering across the section rather than patch a single seam, because the aged material around a patch often fails again at its edges. The deck is then sloped toward its drains, and the drains are cleared and checked before the new surface is laid.

Drainage is the part most often missed. A deck that drains to a clogged outlet or a gutter that has lost its connection will hold water through every storm, and the framing beneath it pays for that over the years in soft boards and stained ceilings below.

Where does a triple-decker leak first?

The wall-to-roof junction, the chimney and the back stair landing are the usual leak points, because they are where different materials meet.

The wall-to-roof junction is the first place to look. Where the top-floor wall meets the roof edge, the flashing has to shed water over the wall covering, and a gap there lets water run down inside the stud bay for years before a stain shows on the ceiling below.

Chimneys on these houses rise through the low-slope deck, and each penetration needs flashing set into the masonry and carried over the deck surface. The back stair landing and the porch roof are other common places, where a post or rail is fixed through the covering and the fastener becomes the path for water.

A leak on an upper floor often starts well away from the stain, so the roofer should trace it from the attic down and check each junction in turn. Patching the ceiling and assuming the job is finished is the most common reason a triple-decker leak returns after a single season.

How does the staging change the scope?

Staging changes the labor and the safety, and a scope that treats a three-story job like a one-story job will be short on both.

Scaffold or tower work on three stories is set up before the roof is opened, with fall protection suited to the height and a clear route for debris. That setup is a separate line on a sound scope and should be written in rather than assumed to be included.

The occupied units make the work more involved. Tenants or owners on each floor may need notice, access to their rooms can be disrupted for a day, and the crew needs a plan for the stairs and the entry during the tear-off, when the house is most exposed to weather.

Ask how long the staging is expected to stand, whether it is taken down each night, and how the crew will handle a rain forecast in the middle of a tear-off. Those answers show whether the plan has been thought through or only described in general terms.

What should a triple-decker scope name?

A triple-decker scope names each roof section, the flashing at each wall, the low-slope deck, the drains and the staging, rather than a single line for the whole roof.

Break the roof into its sections: the main hip or gable, the top flat deck, the rear ell, each porch roof and any dormer. Each section has its own pitch, covering and drainage, and a scope that lumps them together hides the differences that cause the later problems.

Name the flashing at each wall, chimney and penetration, and say whether it is replaced or reused. Name the deck drains and whether they are cleared, reset or replaced. Name the decking allowance for any soft boards found beneath the low-slope surface once it is opened.

Name who removes the debris and where the container stands, and who repairs any damage the work causes to porch rails, gutters or a neighboring wall. A scope that stops at the roof surface leaves the most likely disputes unsettled until the crew has already started.

What should the homeowner ask before work starts?

Ask about the layers, the deck, the drains, the staging and the registration number, and get each answer in writing before the crew arrives.

Ask how the crew will reach the top roof and the rear ell, what happens to the tenants during the work, and whether the deck is being replaced or only covered. Those answers are short, and they show how much thought went into the plan.

Ask for the Massachusetts home improvement contractor registration number and check it with the state regulator before a contract is signed. Sources describe the registration as covering owner-occupied homes of one to four units, so a rental building may fall under a different arrangement. Ask the regulator to confirm which applies.

Keep the written scope, the photographs and the final inspection note together. A triple-decker roof can shelter several households at once, and the record of the work should be as complete as the roof that was repaired.

How should a triple-decker be maintained between jobs?

Between jobs, a triple-decker needs a yearly walk of its flat sections, a check of its drains and a look at each wall junction after the big storms.

A yearly walk of the low-slope sections shows the first signs of trouble: ponding water that stays after rain, a seam that has opened, granules or surface material collecting in the drains, and a lifted edge where the deck meets the wall. Each sign is cheap to note and expensive to ignore.

Clear the drains before the heaviest weather of the season. A drain that is clogged in a storm is the most common cause of water standing on a flat deck, and the water then works into the seams that were already tired. Ask the roofer to check the drains and the outlets together.

Keep the walk and its findings with the original scope. A dated list of what was seen, with photographs of any ponding or damage, lets the next visit start where the last one ended rather than from the ground up.

Frequently asked questions

Is a triple-decker roof always flat?

No. Many have a flat or low-slope top with a steeper main roof over the front, and the rear ell and porches are often low-slope. Each section should be looked at on its own pitch and covering.

Why does the upper floor leak when the roof looks fine from the street?

Water often enters at a wall junction, a chimney or a penetration and travels along the framing before it reaches a ceiling. Tracing it from the attic down is the way to find the entry point, because the stain can sit well away from it.

Do triple-deckers need more staging than other roofs?

Usually yes, because the eave is three stories up and the rear is often reached only by porch or stair. The staging plan is part of a sound scope and should be written in rather than left out.

Can a low-slope section be reroofed without replacing the whole deck?

Sometimes, if the deck is sound and the drains work. A sound scope says what was found under the surface before it recommends a partial job, and it does not assume the deck is good until it has been checked.

Who should I contact about a shared roof in a multi-unit house?

Call the roofer about the roof, and contact the owner or manager of the building about access and notice to the tenants. The building department covers the permit question for the address, and the roofer should confirm the scope in writing.

This guide is general information for Bristol County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Still stuck? We pick up 24/7.

If it's an emergency, call now. For non-urgent help, send the form and we'll call you back.

Keep reading

More guides

WhatsApp