Phones answered 24/7New Bedford, MA
Call (833) 751-2102
Phones answered 24/7Call any time(833) 751-2102
Serving Bristol County

Roof leak diagnosis and flashing repair for old New Bedford houses

The leak is traced to its entry point, the flashing that failed is rebuilt, and the joint is tested before the crew leaves.

  • Leaks, flashing and tear-offs
  • Triple-deckers and low-slope decks
  • Coastal wind and storm damage

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Leak Diagnosis

Leak Diagnosis and Flashing Repair: what it covers

Quick answer

Leak diagnosis and flashing repair means finding where water actually enters a roof, then rebuilding the metal and membrane at that joint so it sheds water. New Bedford Roofing traces leaks across New Bedford and the surrounding towns, and a call to (833) 751-2102 starts with a few questions about when the stain appeared.

Leak Diagnosis and Flashing Repair illustration for New Bedford, MA

Most leaks in older houses do not come from the open field of shingle. They come from a joint: where the roof meets a wall, a chimney, a dormer or a vent pipe. Those joints are built from several pieces of metal and sealant that were set at different times, and the place where they meet is where water finds its way in. A roofer who understands the joint can usually find the leak in a single visit.

The difficulty is that water does not appear where it enters. It runs along a rafter, drops at a nail, and shows up on a ceiling several feet away. The diagnosis therefore starts in the attic and works back to the roof surface, following the stain upward until the dry wood at the top of the trail shows where the water came in. That method is slower than walking the roof, but it is more accurate.

Once the entry point is found, the repair is usually straightforward in principle and careful in practice. The flashing is lifted, the failed piece is replaced or reset, and the surrounding shingles are returned to their courses. The joint is then tested with water, so the repair is proved against the same conditions that caused the leak rather than assumed to be right.

Service area
New Bedford & Bristol County
Availability
Phones answered 24/7
Warning signs

Signs you need leak diagnosis and flashing repair

Water in a ceiling can hide a heavy, sagging section of plaster or a damaged joist, so keep out from under a bulge and do not press on it. Stay off a wet roof and do not try to reach a flashing joint from an unsafe ladder. Turn off the power to any light or outlet in the wet area before going near it.

  • A ceiling stain near an exterior wall that grows after heavy rain
  • A stain that appears only when the wind blows from one direction
  • Rusted or cracked metal visible at the base of a wall or chimney
  • Sealant that has shrunk, split or peeled away from a joint
  • Dark wood or a damp smell in the attic beside a rafter
  • A dormer cheek or wall with staining that begins at the roof line
  • Water dripping from a light fixture or a vent pipe after rain
Our process

How our leak diagnosis and flashing repair visit works

  1. Trace the stain from the room

    The crew starts with the ceiling or wall that shows the leak and notes its position against the walls and the roof framing. Photographs and measurements are taken so the path can be followed upward. A stain near a wall is often a leak at the wall above it, and a stain in the middle of a room may come from a point a few feet away.

  2. Follow the water in the attic

    In the attic the crew traces the wet path along the rafters and the sheathing, looking for the highest point of darkened wood. A moisture meter helps to confirm which boards are still wet. The highest dry point of the trail, the place where the wet stops moving upward, is usually within a foot or two of the entry.

  3. Inspect the joint from the roof

    On the roof the crew checks the joint identified in the attic: the step flashing along a wall, the counter flashing into the brick, the apron at the bottom of a slope, or the collar around a vent. The metal is checked for rust, lifting and open seams, and the sealant is probed for cracking or shrinkage.

  4. Rebuild the failed piece

    The failed flashing is removed and replaced, not patched over. New step flashing is woven into each course of shingle, and counter flashing is set into a reglet or mortar joint so that it sheds water over the top of the step. The shingles are returned to the courses above and below the repair.

  5. Water-test the repair

    Water is run over the repaired joint from a hose, starting low and working up, while someone watches the attic. The test is repeated for the same length of time the leak was reported to take. A repair that passes the test is closed up, and the result is written into the scope so the homeowner knows it was proved.

Job stories

Typical jobs for leak diagnosis and flashing repair

Typical job
Illustration: A typical valley leak in a New Bedford triple-decker

A typical valley leak in a New Bedford triple-decker

What homeowners notice
A stain appears on the ceiling of the top-floor bedroom, several feet from the nearest outside wall, and it grows after each of two heavy rains. The covering looks undisturbed from the street.
What we do
The technician works from the attic, follows the darkened decking upslope to the metal in a valley and finds the trough thin and open at a lap. The valley metal is replaced and the shingle courses on either side are relaid into it.
What to expect
The findings record the stain, the wet attic bay and the open lap, with photographs before and after, and the homeowner is shown the path the water had been taking.

Why does water travel so far from where it enters?

Water entering a roof runs along whatever surface it meets, and it follows gravity and any gap in its path. The stain on the ceiling marks where it finally dropped through, which can be far from the place it got in.

A drop of water that enters at a flashing joint may run down a rafter, cross a nail and soak insulation for several feet before it reaches the ceiling. In an older house with plaster and lath, the water can also run inside a wall cavity and appear at a baseboard on the floor below. That is why the diagnosis follows the wet wood upward instead of trusting the stain.

Why is the flashing more often at fault than the shingles?

Shingles fail as a field, while flashing fails at the places where two materials meet and the seal is only as good as the sealant or the fastener at that point.

A shingle field sheds water as long as its courses lap properly and are not cracked, so a leak through the field usually means a large area has failed. A joint, however, depends on several pieces working together. Metal that rusts at one edge, sealant that shrinks away from a brick joint, or a counter flashing that was never set into the mortar will each let water through, even when everything around it looks sound.

What does a proper repair look like at a wall junction?

A proper repair replaces the failed flashing with new step pieces woven into the shingle courses, and sets any counter flashing into the wall so it sheds water downward.

The steps are placed one shingle at a time, each overlapping the course beneath, so that water always runs out and over the shingle below. Sealant is a secondary defense at the joint, not the primary one. A repair that relies on sealant alone to hold a flashing joint is likely to fail again within a few seasons, and the scope should say how the metal sheds water without it.

Why test the repair with water?

A water test is the only way to prove a flashing repair works under the conditions that caused the leak. A repair that looks correct can still leak when water is driven against it.

The test runs a hose over the joint from the bottom up, for long enough to match the rain that caused the problem, while someone watches the attic. If the joint leaks during the test, the crew finds the cause before it leaves and does not close the roof over an unproved repair. The result is recorded in the scope.

Options

Types and options for leak diagnosis and flashing repair

Step flashing along a wall

Where a sloped roof meets a sidewall, short pieces of step flashing are woven between each shingle course. When one piece fails, water runs behind the wall covering. The repair lifts the courses, replaces the failed pieces in sequence, and checks that each one overlaps the one below it.

Headwall and chimney flashing

A headwall is the wall that the roof runs up against, usually at the top of a slope. The flashing there is often a single strip of metal and sealant, which fails at the corners. The repair rebuilds the headwall flashing with step pieces and a counter flashing turned into the wall, sealed with the right material.

Dormer cheek and valley junction

Dormers add a set of junctions where the cheek walls meet the roof and where the valley runs into the dormer roof. Those points carry a lot of water, and they are often poorly detailed on older houses. The repair rebuilds the valley metal and the flashing at the cheek, and the dormer walls are checked for staining above the roof line.

Pipe boots and vent collars

The rubber boot around a pipe cracks with age, and the collar on a vent lets water run down the pipe. Both are small, common leak points. The repair replaces the boot or the collar and sets it into the shingle courses so that each layer overlaps the one below.

Apron and eave transitions

The apron is the flashing at the lower edge of a wall that meets a roof slope, and it is where water runs off the wall onto the roof. When the apron fails, water enters behind the siding at the bottom of the wall. The repair reseats the apron and reseals its edge, with the drip edge kept clear.

Bristol County

Why leak diagnosis and flashing repair is different in the South Coast

Many leaks on New Bedford's older houses trace to a wall junction at the rear of the building, where a flat or low-slope section meets a steeper roof. The flashing there is often the original piece, set in the siding in a way that no longer sheds water.

The brick chimneys on pre-war houses in the city carry their own leak points at the roof line, and a leak near a chimney is often a flashing problem rather than a masonry problem. The chimney flashing repair page covers that joint in more detail.

Along the shore, wind-driven rain works its way under flashing that was sound in a calm season. A joint that leaks only in an easterly or southeasterly storm points to a flashing edge that the wind is lifting, and the repair includes a check of the fasteners at that edge.

Still stuck? We pick up 24/7.

If it's an emergency, call now. For non-urgent leak diagnosis and flashing repair, send the form and we'll call you back.

Related

Roof Repair

The failed section is found, traced and rebuilt, so the rest of the covering can stay on for years.

Chimney Flashing Repair

The metal that seals the chimney to the roof is rebuilt, and the mortar it sits in is checked where it has opened.

Emergency Roof Tarping

A secured tarp keeps rain off an open roof for the time it takes to schedule the real repair.

Guides

Read before you book

What a three-story roof asks of a crew

A triple-decker is three stories of wall under a roof that is often flat, low-slope or hidden behind a parapet, with a rear ell and porch roofs beside it.

A checklist for the roof after a big storm

After a hurricane or strong wind, most of the damage that matters can be seen from the ground, in the attic or at the flashing, and it is worth finding before the next rain.

FAQ

Leak Diagnosis and Flashing Repair FAQs

How do you find a leak if the stain is in a different place from the roof damage?

The stain is followed back to its source through the attic, where the path of the water is easier to see. The highest dry point along the wet wood is usually the entry, even when it is several feet from the stain on the ceiling.

Is the flashing or the shingle to blame for most leaks?

On older houses the flashing at a wall, chimney or dormer is more often the cause, because it is a joint where several materials meet. A leak through the open field of shingle usually means a larger area has failed, and the scope says which of the two it is.

Can the joint be sealed with caulk instead?

Caulk can help as a secondary seal, but it is not a substitute for flashing that sheds water. A joint sealed only with caulk tends to fail again after a few seasons, so the crew replaces the metal and uses sealant to finish the joint, not to carry it.

Why does the water test take so long?

The test has to run for long enough to match the rain that caused the leak, and water must be applied from the bottom up so that it reaches the joint from the way it would arrive in a storm. A short test that passes can miss a joint that fails under sustained wind-driven rain.

Will you repair the leak if the roof is nearing the end of its life?

Yes, a flashing repair can stop an active leak even on an older roof. The scope will say whether the rest of the covering is likely to last through the next season, and it will recommend a replacement if the surrounding shingles are no longer able to hold the new work.

How do I start the call?

Say where the stain is, whether it appears during rain or wind, and how long it has been there. Those three facts usually point the crew toward the right joint before it goes up the ladder. Call (833) 751-2102 to arrange a visit.

WhatsApp