Fastest: call (833) 751-2102. Or send this and we call you back.
Triple-Decker Roofs
Triple-Decker Roof Replacement: what it covers
Quick answer
A triple-decker roof replacement is a re-roof on a three-story, multi-unit building, usually with a low-slope or nearly flat section over a rear wing or porch. New Bedford Roofing plans the access, the staging and the tenant notice before any old covering comes off, and calls for New Bedford and the towns around it go to (833) 751-2102.
The triple-decker is the building type that most often defines a New Bedford roof problem. Three stacked apartments, a shared side wall, a narrow yard and a rear roof that sits low over a kitchen wing make an ordinary re-roof into a staged project. Nothing about the work is exotic. What changes is the sequence, because people are living directly beneath the covering the whole time it is being removed.
The rear and porch sections are where the water tends to find its way in. A pitched main roof may be in fair condition while the flat or low-slope piece behind it has ponded, seamed open and let water run down the wall. A roof replacement that treats the building as one plane misses those sections, so the survey walks each part of the building separately and notes where the planes meet.
Access is the other constraint. A ladder footed on a narrow side yard, a dumpster that cannot sit in the drive, and a neighbor whose wall is a few feet from the eave all affect the schedule. The first call asks how many units the building holds, whether there is a driveway or only a sidewalk, and whether the side wall is shared, because those answers decide how the crew will get material up and debris down.
Triple-decker work is high work with people living inside. Crews use fall protection on steep and low-slope sections, secure ladders at the base and the top, and keep the work area fenced off from the walkway. Tenants should keep their windows closed where the work is overhead and stay clear of the debris chute and the ladder.
A top-floor ceiling stain that shows up on the wall of the rear bedroom
A low-slope rear roof that holds water for a day or more after rain
Seams lifting or blistering along the edge of a flat section
Brick or stucco wall staining directly beneath the junction with a flat roof
Shingles on the pitched main roof with cupping and granule loss on the front slope
Flashing at a parapet or party wall that has been patched with sealant more than once
Gutters that overflow onto a neighbor's wall at a shared lot line
Our process
How our triple-decker roof replacement visit works
Survey each section of the building
The pitched main roof, the rear wing and each porch are surveyed as separate planes. The crew notes where a low-slope section meets a steeper one, where a parapet rises, and where a party wall sets the edge. That map becomes the basis for the scope, because each junction needs its own detail.
Plan access and tenant notice
The access plan sets where the ladder or hoist will stand, where debris will be staged, and how the side yard will be kept clear. Tenants in each unit are told the working days and the hours, and the crew agrees which windows and doors will be kept closed while the old covering is being removed.
Protect the top floor first
Before the old covering is stripped, the top-floor ceilings are protected with sheeting and the attic hatch is sealed. Any skylight or hatch is covered. The stripping then runs in sections, so no more of the building is open to weather at one time than the crew can close up by nightfall.
Rebuild the low-slope sections
Flat and low-slope sections get a membrane system laid to a sound deck with the correct slope toward the drains or scuppers. Seams are welded or sealed to the manufacturer's method, and wall flashing is turned up to the parapet or the siding at a height the water cannot reach.
Close, clean and walk the building
The day ends with each section closed in, the site swept and the access cleared. At the end of the job the crew walks each unit's top-floor ceiling and the roof with the owner, showing where the new flashing sits and where drainage has been set, so the next inspection has a reference point.
Why do triple-deckers need different roof work?
Three stacked units, a shared wall and a rear roof that sits low make the building one job in several parts, and each part needs its own inspection and detail.
A roofer working on a single-family house sees one slope and one ridge. On a three-story building the same roofer sees a steep front, a flat rear, a parapet at the party wall and a porch that carries its own roof. Each of those is a different system, and the scope has to assign the right membrane, flashing and fastener to each, not apply one material across the whole footprint.
How is the work sequenced around people who live there?
The sequence protects the top unit first, opens only as much roof as can be closed in a day, and gives tenants notice of the days and hours that affect them.
A crew that strips the whole roof on Monday and leaves it open until Friday exposes the top floor to every shower on the coast. Working in sections, with sheeting in place over each finished area, lets the building stay dry. Tenants who know the schedule can plan around the noise and the hours on the ladder, which makes the job easier for everyone.
What is the shared-wall question?
Where the building shares a wall with a neighbor, the roof edge and the gutter may sit within a few feet of the neighboring house, and that affects both access and drainage.
Water shed from a triple-decker roof at a shared lot line can run onto the neighbor's wall, and a gutter that overflows there becomes a complaint. The survey notes the lot line, the gutter condition and any downspout that discharges at the side. The fix is often a longer downspout or a splash block, which the scope can include without touching the neighbor's property.
Does a multi-unit building change the permit question?
It can. The permit requirement depends on the town and on the scale of the work, so the building department of the city or town should be asked before the job starts.
Multi-unit buildings sometimes fall under different rules from single-family houses, and the answer for New Bedford or a neighboring town is not something this site can state from its sources. The building department can say whether a permit is needed and whether the work must be inspected. Put the answer in the scope so the owner and the crew agree on it before the first day.
Options
Types and options for triple-decker roof replacement
Pitched main roof over the front block
The front of a triple-decker is usually a pitched roof with a gable or hip end. It is replaced like any steep roof, with the underlayment, drip edge and shingles laid from the eave up. The main work is at the valley where it meets the rear section and at the chimney that often rises through it.
Low-slope rear wing
The rear section over a kitchen or back stair is often close to flat. It needs a membrane or a rolled roofing system with a clear slope to drains, and the seams are where most failures begin. The scope records each seam and each penetration, because a single open seam can leak for months before a stain appears.
Porch and stair roofs
Front and rear porches are small roofs with a lot of junctions. Their decks rot from the edge inward, and their flashing is often the original piece tucked under the siding. Replacing them usually means lifting the siding to set new flashing properly, which the scope includes so the work is not done from the surface alone.
Parapet and party wall flashing
Where a roof runs into a masonry parapet or a shared wall, the flashing carries the water up and over the edge. Those joints are often sealed with mortar or caulk that cracks within a few seasons. The repair cuts a reglet or uses a counter flashing set in the mortar joint, so it is not dependent on sealant.
Rear hatch and roof access
Many triple-deckers have a hatch or a stair to the roof from the top unit. The hatch is a penetration that can leak around its frame, and it is also the crew's route on and off the roof. Its curb and flashing are rebuilt, and the scope notes whether the hatch needs to be kept secure during the work.
Bristol County
Why triple-decker roof replacement is different in the South Coast
The triple-decker is a defining building type in New Bedford and in the older mill cities nearby. Its roofs carry the particular problems of tall, shared construction: low rear sections, shared walls and long drops to the ground. A crew that has worked on these buildings plans the access and the protection of the upper floor before it writes the scope.
Fall River, a short drive from New Bedford, has a similar stock of older multi-unit housing, and many owners there face the same staging questions. The principles are the same across the two cities, but the specific side yards and party walls differ from one block to the next, so the survey is done on the building itself.
Owners of older multi-unit buildings often ask whether the roof can be replaced in stages, with one unit's section done each season. That is sometimes possible, but the flashing and the drainage must be tied together at each stage, and the scope should be written so that the first stage does not leave a weak joint for the second.
Still stuck? We pick up 24/7.
If it's an emergency, call now. For non-urgent triple-decker roof replacement, send the form and we'll call you back.
This guide prints no dollar figure, because no verified New Bedford or Massachusetts price was found, and a national average says little about a city of old, tall houses.
A triple-decker is three stories of wall under a roof that is often flat, low-slope or hidden behind a parapet, with a rear ell and porch roofs beside it.
Massachusetts registers home improvement contractors through the Office of Consumer Affairs and Business Regulation, and sources describe that registration as covering roofs on owner-occupied homes of one to four units.
Permits are issued town by town on the South Coast, so no single rule settles whether a roof replacement needs one.
Read the guide
FAQ
Triple-Decker Roof Replacement FAQs
Can you work on the roof while tenants are still living in the building?
Yes, that is the normal case. The work is planned so that the top floor is protected at each step, the access is kept clear, and tenants are told the days and hours when the crew will be overhead. Nobody needs to move out for the job.
Why does the rear section need a different covering from the front?
A steep pitched roof sheds water quickly, while a flat or nearly flat section holds it. The rear section needs a membrane or rolled system with a slope to drains, and the front needs shingles laid over a drip edge. Using one covering for both would fail at the rear.
How do you handle the parapet or the party wall?
The flashing is set into the masonry, either in a reglet cut into the wall or under a counter flashing set into a mortar joint. That keeps the water away from the sealant, which is the part that cracks first on these joints, and it is checked after the work is finished.
Will the gutters and downspouts be replaced too?
Gutters are assessed in the same survey, and any section that is failing or discharges onto a neighbor's wall is noted in the scope. The gutter and downspout repair page covers the details, and the crew will say which pieces it recommends alongside the roof.
Do you need access to the inside of the building?
Access to the top-floor unit is needed to protect the ceilings and to check the attic or the underside of the deck. The crew arranges that with the owner or the tenant ahead of the first day, and it is done with notice and at a time the occupant agrees to.
Who should I call first about a triple-decker roof?
Call (833) 751-2102 and say how many units the building holds, whether the side wall is shared and what the low-slope sections look like. That lets the crew schedule a survey that covers every part of the building, rather than a single visit that looks only at the front.