Fastest: call (833) 751-2102. Or send this and we call you back.
Chimney Flashing
Chimney Flashing Repair: what it covers
Quick answer
Chimney flashing repair means rebuilding the metal that joins a chimney to the roof: the step flashing along its sides, the counter flashing set into the brick, and the saddle or cricket on its uphill face. New Bedford Roofing repairs these joints across New Bedford, and calls go to (833) 751-2102.
The chimney is one of the most common sources of a leak on an older house in New Bedford. A brick stack that has stood for seventy or a hundred years meets a roof that has been re-covered several times, and the joint between them is where the two systems have to be sealed.
The flashing is the sealing system, and the mortar is the surface it is set into. A counter flashing is a strip of metal let into a groove cut in the brick, or into a mortar joint, so that water runs down the face of the chimney onto the step flashing below. Where the mortar has opened, the counter flashing loses its anchor, and water works behind it.
A wide chimney on a steep roof also needs a saddle or cricket on its uphill side, a small pitched section that carries water around the stack. Many older chimneys lack one, and the water piles up against the brick instead of running around it. The repair includes a check of that side, since a leak at the top of a chimney is often a missing saddle rather than failed metal.
A chimney is heavy and its masonry can loosen without warning, so no one should stand on the brick or lean a ladder against the stack. Crews working at the roof line use fall protection and secure the ladder to the eave, not the chimney. Homeowners should not try to remove loose brick or metal, and should keep children away from the work area below.
A stain on the ceiling or wall beside the chimney that grows after rain
Cracked or missing mortar in the joint where the chimney meets the roof
Metal at the chimney edge that has rusted, lifted or pulled from the brick
Water staining on the brick face below a roof-line joint
A chimney crown with cracks running from the flue opening outward
Sealant along the flashing that has shrunk, split or disappeared
Dark rings on the attic side of the chimney where it passes through the roof
Our process
How our chimney flashing repair visit works
Check the joint from the attic and the room
The crew looks at the chimney from the room below and from the attic, where the stack passes through the roof. Water stains on the brick, dark rings on the wood and any gap around the flue are recorded. The attic view often shows the leak path before the roof is opened.
Inspect the masonry and the mortar
The brick and mortar at the roof line are checked by sight and by touch. Open joints, loose bricks and cracked crowns are marked, because the flashing is only as firm as the masonry it is set into. A crack in the crown is noted, though the crown itself is a separate repair.
Remove the failed counter flashing
The old counter flashing is lifted from its groove or mortar joint. Its condition is recorded, and any metal that is still sound is kept for the reset. The area it covered is cleaned, so that the new metal bears on sound mortar and not on crumbling material.
Set new step and counter flashing
New step flashing is woven into each course of shingle along the sides of the chimney, and new counter flashing is set into the masonry above it. The groove is cut or repointed so the metal is held firmly. Each piece overlaps the one below, so water runs out over the shingle rather than behind the metal.
Rebuild the saddle and test
Where the chimney lacks a saddle or cricket, one is built on the uphill side and sealed into the shingles. The joint is then water-tested from the bottom up, with a check in the attic during the test, before the roof is closed and the scope is signed.
A homeowner notices a dark mark on the wall beside the chimney after a windy week and hears water when the rain is heavy. The chimney cap looks slightly off line.
What we do
The technician looks at the flashing from the ground and from a secure ladder, then from the attic. The step flashing has lifted at the chimney's downhill side and the mortar at the counterflashing has crumbled. The flashing is reset, the counterflashing is repointed and the cap is refixed.
What to expect
The findings show the lifted flashing, the repointed joint and the wet attic wall before and after, and the homeowner is advised to recheck the chimney after the next heavy rain.
Why do chimneys leak so often on older roofs?
A chimney is a tall masonry block with several joints where it meets the roof, and each joint depends on metal and mortar that age at different rates.
Brick expands and contracts with heat, mortar softens over decades, and metal rusts at the points where it is most exposed. An older chimney has often been repointed and re-flashed more than once, with each repair set on top of the last. The leak usually appears where the newest material meets the oldest, and the repair has to be planned with that history in mind.
Why is the mortar as important as the metal?
Counter flashing is only as firm as the mortar it is set into, so a repair that resets the metal into bad mortar will fail within a few seasons.
Where the mortar has crumbled, the groove that holds the counter flashing is too weak to keep it in place, and the metal lifts when the wind pulls at it. The repointing is therefore part of the flashing repair, not a separate job. The crew cuts out the loose mortar to sound brick and repoints with a material that bonds to the existing joint.
Does a chimney repair need a permit?
It depends on the town and on how much of the chimney is rebuilt, so the answer comes from the local building department rather than a general rule.
Repointing and reflashing are usually treated differently from rebuilding a stack or changing its height, and sources do not give one rule for the whole South Coast. The building department can confirm whether a permit is needed for a particular repair, and the scope should record that answer before any masonry is opened.
What should a homeowner expect from a chimney repair?
A sound chimney repair should include a written list of the metal replaced, the mortar repointed, the saddle built or confirmed, and the test result.
The homeowner should also expect a note on any brick or crown that was found to be failing beyond the scope of the flashing work. Those items are reported separately so that the homeowner can decide whether to address them now or later, and the flashing repair itself is not held up while that decision is made.
Options
Types and options for chimney flashing repair
Counter flashing set in mortar
The traditional counter flashing is a strip of metal sealed into a joint in the mortar above the roof line. When the mortar cracks, the metal can lift and water runs behind it. The repair repoints the joint and sets the metal again, with a sealant used only as a secondary seal.
Surface-mounted counter flashing
Where the mortar is too weak to hold a groove, the counter flashing can be mounted to the face of the brick with a clamp or a surface reglet. This avoids damaging the masonry, though it is more visible. The scope names the method and the reason for it, so the homeowner knows the joint was chosen on purpose.
Saddle or cricket on the uphill side
A saddle is a small pitched section built between the chimney and the roof, which carries water around the stack instead of letting it pool against the brick. It is built from metal sheet and sealed into the shingles. Its absence is one of the most common causes of a leak at the top of an old chimney.
Chimney crown and cap
The crown is the concrete or mortar cap at the top of the stack, and it sheds water away from the flue. Cracks in the crown let water run into the brick and down the flue. The repair seals the crown and checks the cap, with a note that the crown can be rebuilt separately if the cracks are deep.
Side and rear step flashing
Along the two sides of the chimney, step flashing is woven between each shingle course, lifting the water over the shingle below. When one piece fails, it leaves a gap that the wind can drive water into. The repair replaces the failed pieces in sequence, checking each overlap.
Bristol County
Why chimney flashing repair is different in the South Coast
Pre-war brick chimneys are a common feature of the older streets in New Bedford, and their roof-line joints are often the first thing to fail. A crew working on these houses checks the mortar before it trusts the flashing, since the two are bonded together.
Chimneys on the older houses of Fall River and the other mill towns nearby carry the same kind of joint, and their masonry has often been repointed in a patchwork over the years. The repair plan follows what the mortar actually is, not what the house looked like when it was built.
Salt air on the South Coast speeds the corrosion of exposed steel and aluminum at a chimney, especially where a metal cap or a bracket sits near the bay. The scope names any metal that should be replaced with a more durable piece rather than cleaned and reused.
Still stuck? We pick up 24/7.
If it's an emergency, call now. For non-urgent chimney flashing repair, send the form and we'll call you back.
A triple-decker is three stories of wall under a roof that is often flat, low-slope or hidden behind a parapet, with a rear ell and porch roofs beside it.
Read the guide
FAQ
Chimney Flashing Repair FAQs
Can you fix the chimney flashing without repointing the brick?
Sometimes, if the mortar at the joint is sound and only the metal has failed. Where the mortar is open or crumbling, repointing is part of the repair, because counter flashing cannot hold in weak mortar and the reset metal will lift again.
Why is there a leak at the top of my chimney if the flashing looks fine?
A missing or failed saddle on the uphill side is a common cause. Water runs down the roof and piles up against the brick instead of flowing around the stack, and the joint eventually lets it in. The crew checks the saddle as part of the same visit.
Should the chimney be capped?
A cap keeps rain and debris out of the flue and protects the crown, and many older chimneys lack one. Whether a cap is recommended depends on the flue and the crown, and the crew will say so in the scope rather than fitting one as a standard step.
How do you know the crown is failing?
Cracks that run outward from the flue opening, loose or missing pieces of mortar, and water staining down the brick below the crown are the signs. A crown repair is a separate piece of work from the flashing, and the crew reports it on its own line.
Do you use a surface-mounted flashing or a groove?
The choice depends on the strength of the mortar and the appearance the homeowner wants. A groove gives the cleanest finish when the masonry can take it, while a surface mount avoids cutting into weak brick. The scope names the method and the reason.
How do I arrange the visit?
Call (833) 751-2102 and describe where the stain appears and whether it shows during rain or wind. The crew will check the chimney from both the room and the roof, which usually shows the joint at fault in a single visit.