Phones answered 24/7New Bedford, MA
Call (833) 751-2102
Phones answered 24/7Call any time(833) 751-2102
Serving Bristol County

Cedar shake and slate roof repair for older houses on the South Coast

Shake and slate are repaired piece by piece, so the work protects the sound material rather than replacing it.

  • Leaks, flashing and tear-offs
  • Triple-deckers and low-slope decks
  • Coastal wind and storm damage

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Cedar and Slate Repair

Cedar Shake and Slate Roof Repair: what it covers

Quick answer

Cedar shake and slate roof repair means replacing individual shakes or slates, renewing their fasteners and flashing, and leaving the sound pieces in place. New Bedford Roofing repairs these roofs in New Bedford and the South Coast towns, and calls go to (833) 751-2102.

Cedar Shake and Slate Roof Repair illustration for New Bedford, MA

Not every older roof in New Bedford is asphalt. Some of the older houses, and especially those of the South Coast towns, carry cedar shake or slate, and they are repaired in a different way. A shake or slate roof is built of many small units, each held by its own fasteners, and the repair means working on individual pieces rather than whole courses.

Cedar shake is wood, and it weathers, splits and curls with exposure to sun, rain and salt air. The fasteners that hold it can rust, and the underlayment beneath it is often the original, which may have degraded. Slate is stone, and it fails by cracking, slipping or losing its nails. Both materials last a long time when they are maintained, and both are sensitive to the way they are handled during a repair.

The first question is whether the roof is shake or slate at all. Some houses carry cedar on their walls and asphalt on their roofs, and survey records in the area often note asphalt shingle on roofs that were built with shingled walls. A roofer confirms the roof covering before the scope is written, so the repair plan matches what is actually there rather than what the house looks like from the street.

Service area
New Bedford & Bristol County
Availability
Phones answered 24/7
Warning signs

Signs you need cedar shake and slate roof repair

Shake and slate roofs are slippery, brittle and heavy, and they crack under a person's weight. Crews work from a secured ladder or a roof bracket with fall protection, and they do not walk a slate roof in wet weather. Homeowners should not walk the roof, and should keep the area below the work clear of falling pieces.

  • Shakes that have split, cupped or curled at their ends
  • Slates that have cracked across the body or slipped from their nails
  • Rust stains running down the roof face beneath a fastener line
  • Moss or dark staining that holds moisture against the wood or stone
  • Missing pieces along a ridge or hip that expose the underlayment
  • Soft or punky wood at a shake's butt end where it meets the course below
  • A patchwork of asphalt pieces on a roof that was once shake or slate
Our process

How our cedar shake and slate roof repair visit works

  1. Confirm the covering and survey the damage

    The roof is walked, or inspected from a safe ladder, to confirm the material and to map the damage. Each cracked slate, split shake and missing piece is counted and located on a sketch, so the repair can be scoped piece by piece rather than by slope.

  2. Check the fasteners and the underlayment

    Under each damaged piece the fastener is checked for rust, corrosion and loss of holding power. Underlayment that has degraded is noted, since replacing a shake or slate without addressing the layer beneath it simply moves the leak. Fasteners are chosen to match the material and the exposure.

  3. Remove and replace the failed pieces

    Damaged shakes or slates are carefully removed, taking care not to crack the pieces around them. The replacement is cut or chosen to fit the course and set with new fasteners in the correct position. Sound neighbors are left in place, and the surrounding courses are checked for loose nails.

  4. Repair the ridge, hip and flashing

    Ridge and hip pieces are the most exposed on a shake or slate roof, and they are repaired as a set with their fasteners and any flashing at the joint. Metal flashing at a chimney or wall is checked and reset where it has lifted, using a material that will not corrode against the roof covering.

  5. Check the finished roof for loose pieces

    The completed repair is checked by hand for pieces that move, and any loose or unsound item is secured or replaced before the crew leaves. The scope records each repaired area so the next inspection can compare it with the original condition.

Why is piece-by-piece repair better for shake and slate?

Shake and slate roofs are built of many small units, and the sound pieces are worth keeping, so repair targets only the failed units rather than replacing the whole covering.

Replacing an entire slate roof is a large undertaking, and the matched material is not always available in the same thickness or color. A crew that repairs piece by piece keeps the sound slates and shakes in place, which preserves the original character of the roof and the investment in it. The skill lies in removing a failed piece without damaging its neighbors.

What makes a cedar roof different from an asphalt one?

Cedar is wood and it moves with moisture, so its repair must allow for swelling and shrinking and must use fasteners that do not corrode into the wood.

Shakes are laid with a gap to allow for movement, and a repair that closes that gap can buckle the course. Moss and debris that hold moisture against the wood accelerate decay, so the roof is cleared where it is safe to do so. Fasteners are chosen to hold without staining the cedar, and the scope names the type.

Why check the underlayment during a shake or slate repair?

The underlayment is the layer that keeps water off the deck, and on an older roof it may have aged far beyond the covering above it.

Where the underlayment has degraded, water can reach the deck even when every piece of covering is sound. A repair that ignores the layer beneath it will leak again, sometimes from a place that appears sound from above. The crew checks the underlayment at the damaged areas and records what it finds.

Is a permit needed for a shake or slate repair?

It depends on the town and on the scale of the work, so the answer comes from the local building department.

A piece-by-piece repair is usually a smaller job than a re-roof, but sources do not give one rule across the South Coast, so this site does not state one. The building department should be asked before a larger repair is started. The scope records the answer alongside the description of the work.

Options

Types and options for cedar shake and slate roof repair

Split or cupped cedar shakes

Shakes split along their grain or cup at the ends when they dry and wet repeatedly. A split shake can be replaced with a new one cut to fit, and a cupped shake is often flattened or swapped. The repair checks the course below, since a split above it can indicate a problem with the underlayment.

Cracked or slipped slate

Slate cracks when it is struck, when a nail fails or when the deck moves. A cracked slate is replaced, and a slipped slate is re-set on new fasteners. Slate can be repaired piece by piece, which is one of its advantages over a whole-roof replacement, provided the pieces are matched in thickness.

Fastener failure and copper or stainless nails

Where the nails have rusted or pulled through, the piece they held is at risk. Repair uses corrosion-resistant fasteners, typically copper or stainless, that match the material and the exposure. Plain steel nails near the bay corrode quickly, and the scope names the fastener used.

Ridge and hip repair

The ridge and hip are the highest and most exposed lines on the roof. Damaged ridge pieces are replaced as a set, and the fastening along the line is checked. Wind on the bay side loosens these pieces first, so the repair includes a look at the entire ridge run.

Underlayment beneath shake or slate

The layer under a shake or slate roof keeps water away from the deck, and on older roofs it may be the original felt or a material that has degraded. Repairing the covering over a failing underlayment is a temporary measure, so the scope states whether the underlayment was checked and what was found.

Bristol County

Why cedar shake and slate roof repair is different in the South Coast

Padanaram and the older shore houses of South Dartmouth carry cedar shingles on their walls, and some owners assume the roof is cedar too. Local survey records often note asphalt shingle on the roof of an older house, so the roof is checked before the repair is planned.

Slate and older wood roofs are found on a number of the older houses in the wider area, and a crew that works on them keeps replacement pieces on hand in the common sizes so a repair does not wait on a supplier.

Salt air and wind on the bay shore wear down the fasteners and the edges of shake and slate faster than they wear the field. The repair focuses on those edges and on the fastener type, since the field is often still sound.

Skip the guesswork. Call for a straight answer.

Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what cedar shake and slate roof repair should cost.

Related

Roof Repair

The failed section is found, traced and rebuilt, so the rest of the covering can stay on for years.

Chimney Flashing Repair

The metal that seals the chimney to the roof is rebuilt, and the mortar it sits in is checked where it has opened.

Roof Inspection Report

A written report records the roof's condition with photographs, so the owner, a buyer or a landlord can act on the facts.

Guides

Read before you book

FAQ

Cedar Shake and Slate Roof Repair FAQs

Can a cracked slate be repaired rather than replaced?

Yes, a cracked slate is usually replaced on its own, with a matched piece set on new fasteners. The rest of the roof does not need to come off, which is one of the main reasons slate is repaired rather than replaced whole.

Why does the crew avoid steel nails?

Plain steel nails corrode quickly in salt air and can stain or split the material they hold. Copper or stainless fasteners last longer and hold without rust marks, and the scope names the type used on the job.

My house has cedar walls. Is the roof cedar too?

Not necessarily. Some houses carry shingle on their walls and asphalt on their roofs, and local survey records often note asphalt on roofs of older houses. A roofer checks the covering before planning the repair, so the work matches what is actually on the roof.

How long will a repaired shake or slate roof last?

The repaired pieces can last as long as the sound material around them, provided the underlayment and fasteners are sound. The scope states what was checked and what was repaired, and it says where the roof is nearing the end of its life.

Do you keep matched slate or shake in stock?

Replacement material is sourced in the common sizes and colors, and where a match is not available the scope says so. A crew that knows the sizes in use on the older houses of the area can usually find a close match for a single piece.

How do I book a repair?

Call (833) 751-2102 and describe the material you believe is on the roof, the location of the damage and any leaks. The crew will confirm the covering and schedule a visit to map the damage piece by piece.

WhatsApp